Revised Review: Hope Tech Enduro – Pro 4 29er conventional 32spoked

I bought them in 2016, Since February 2017 I added a lot of pictures and improved the review.

I put the 3 wheel sets to more some more abuse, and a lot of hard riding, urban mtb and trail riding, and they survived.

I have put it through harsh riding in all different weather and temperatures.

Rider weight:

ca 75kg with all gear on.

Winter riding:

Aa the temperature decreases seals shrink, wheels go out of true faster, but this will happen on any wheelset.

So far I have been riding down to -11 Celsius.

I have been riding below freezing temperatures, few weeks, I noticed the sound coming from the rear hub was dampened, and sounded like there was water inside, because there was water inside, the plastic seal shrinks when its so cold, which allows water/melting show to come inside, which happen on a -6 Celsius ride. But it’s not possible to make a tighter fitting seal, so I recommend to put grease between the seal and the hub freehub body, which will give more protection after I have applied grease to the seal, I have not had any more issues with water in the freehub. but don’t make a mess, clean up the access to avoid attracting dirt.

I also put grease in the rim holes and on the spoke nipples, provides prevent corrosion.

After a long time of riding the front hub did not need service.

 

The wheel stays quite true, but when it it goes off center to the left both on front and rear, but I regurally check hte wheels, so the tention is good and I keep them qutie true and centered, I have 3 sets in 29. I bought a set for my 6300 too.

 

Pros:

  • provides a true wheel for longer than 28 like Bontrager duster.
  • Hope made a noticeably stiffer wheelset than Bontrager duster 29er when going fast in berms or landing jumps, or in general hard riding, it really makes a huge difference
  • High-quality brass spoke nipples, accurate size, so easy to work with, unlike the nipples on Bontrager Duster wheelset. There is no twisting or bending or crushing or cracking of the nipples when truing the wheel.
  • It has an almost idiot proof design, it’s very easy to take apart, I love the freehub system, there is no too required to take off the freehub.
  • 10 & 11 speed compatible, hope provides a spacer for 10 to 11  speed cassettes, and the freehub body is wider than a 10 speed freehub boy, so the cassette is further to the right/closer to the frame, which results in a better chain line, for 11 speed,and no chain drop when backpedalling, unless you backpedal using your hands at unrealistic speed/rpm, I have been doing backward 180’s without any issues.
  • The wheels stayed true for a long time & no damage to the rim was done, after 3 weeks of hard trail riding, and some hard street riding, but after those 3 months it needed a quick retention, but it was a piece of cake.

 

  • the freehub is not too loud.
  • end caps for skewer or 12mm & 15mm axles
  • very easy to do maintenance/service no springs jumping out or tools needed(not counting the cassette tool)

I managed to get a small dent in 2 spoke nipples, but it did not affect the threads, might have been a big stone that hit them, the dent was only one side so I could get the spoke tool on.

Cons:

  • not the highest engagement, there are other options on the market that provide better engagement, Industry Nine, Chris King, and the king of engagement Onyx due to the clutch, it provides infinite engagement, but they all cost a lot more. the engagement is ok, it does not feel awkward like the cheaper Shimano hubs do.
  • Cassettes with separate cogs Shew up the freehub body, So after some weeks or months, I have to file down the bumps to get the cassette on & off easily.The damage you can see on splines is caused by the cassette pitting into them, If you ignore this for too long you might struggle to get the cassette off, So I used 100 sandpaper to smoother the surface. I want a stronger Freehub body,  I haven’t tried Steel Freehub body or XD driver yet. Some other brands claim to have strong enough free hubs to not wear like this, but I haven’t tried any of them. but I used these since 2016 so that’s quite a long time, but they will probably last me few more years.

 

on my 26er wheel-set: After few short rides Shimano XT  11-46T cassette:

 

Unboxing:

 

 

The Rim:

 

Rock strikes

 

Dent, I bent back with an adjustable wrench but there is still a lump.

A closer look at the Pro 4 hub:

The axle:

 

The bearings & plastic seal.

Springs eventually wear out:

this is to be expected, it’s normal, springs eventually fail.

 

Worn out leaf spring.
Enter a caption

Enter a caption

Maintenance:

 

Shewed up Freehub body:

 

After 1 meter drop with too low tyre pressure: we all make mistakes

A good thing is that I learn from my mistakes and never do them again.

one of the rear wheels got a small dent,  I ridden with studded Suomi WXC 300 tyres,  30 psi was too low in turns because of squirming, but I later added 10 psi.

If can, of course, bends it back.

The sumemr of 2018 I dented the rear wheel on wooden stairs, due to valve stem loosening up:

I fixed the rim in few seconds, there was Loctite on the threads & tightened with pliers, but it still had to be regularly checked I should have done it earlier, that was my fault. I rode up wooden stairs, hit the staircase, and the tyre got a hole near the bead.
which I managed to fix by letting the tyre stay still overnight with 20psi with the hole down.
it sealed up. I had Orange seal, but I filled it up with more as it was spraying after the hit.

Verdict:

Hope offers a wheelset that can take major abuse, for a cost-effective price, But it’s not the ultimate package. the freehub body should be stronger.

If you get this wheelset on sale it’s a good deal.

But I want to try other hubs like Onyx with more engagement for my next bike.

http://www.hopetech.com/product/hope-tech-enduro-pro-4/

Hope has also made a 35mm version  http://www.hopetech.com/product/hope-tech-35w-pro-4/ which I have not Tried.

You can buy it here:

https://www.amazon.co.uk/dp/B01N5B9Y0R/ref=sr_1_1?ie=UTF8&qid=1487380214&sr=8-1&keywords=hope%2Btech%2Bpro%2B4%2Benduro&th=1&psc=1

different hub sizes and colors:

https://www.bike24.com/1.php?menu=1000%2C2%2C140%2C209;mid%5B222%5D=1;content=7

Advertisements

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

w

Connecting to %s